Mazda 3 (2004-2009) - Oil and Filter Change

Mazda 3 (2004-2009)

Production	2004-2009
Platform	Ford C1 platform
Engine(s)	1.4 L MZR I4 1.5 L MZR I4 1.6 L MZR I4 2.0 L MZR I4 2.3 L MZR I4 1.6 L MZ-CD I4 2.0 L MZR-CD I4
Transmission(s)	5-speed automatic 4-speed automatic 5-speed manual 6-speed manual
Length	2004-06 i Sedan: 178.3 in 2004-06 s Sedan: 4540 mm (178.7 in) 2004-06 Hatchback: 4485 mm (176.6 in) 2007-09 i Sedan: 177.4 in 2007-09 s Sedan: 177.6 in 2007-present Hatchback: 176.8
Width	1755 mm (69.1 in)
Height	1465 mm (57.7 in)
Curb weight	1180-1315 kg (2600-2900 lb)

Reminder: Remember, it is illegal to dispose of used motor oil improperly. Before doing this procedure, we recommend you find a local quick-lube place that will accept your dirty oil at no charge.

Contents 1 Tools Needed 2 Supplies Needed 3 Instructions 4 Videos 5 See Also

[edit] Tools Needed

• 10mm socket
• 17mm socket
• Small slotted screwdriver
• Torque wrench with a range of 10 n-m (88.5 lb-in / 7.4 lb-ft) to 30 n-m (265.5 lb-in / 22.1 lb-ft)
• 6mm hex head socket
• 76mm cap type oil filter wrench (14 flute)
• Oil drain pan
• Ramps, lift or jack stands to raise the car for safe access

[edit] Supplies Needed

• 4.25 quarts of API Service grade SL or SM motor oil.
  • The owners manual for U.S. model Mazda3's strongly implies that you must use only 5w20 weight motor oil, but the only requirement is that you use oil that matches the API Service Grade your owners manual calls for.
• Oil Filter Cartridge and two O-Rings
  • Originally the filter cartridge and each O-Ring were sold separately, now any of the filter cartridges you will buy should include both required O-Rings in the package.
  • Part numbers for Mazda and aftermarket oil filters:
    • Mazda OEM L321-14-302-9U
    • Purolator L15505
    • PureOne PL15505
    • WIX 57203
    • Napa 7203
    • Fram CH9641
    • Fomoco 2170 (2.3l engine)

[edit] Instructions

1. The first obvious step is to raise the car so you can access the underside. Be sure to use proper safety equipment & precautions.
2. Open the hood to access the top of the engine.
3. Remove the engine's plastic cover by pulling up gently on the 2 back corners & middle center.
   

   
   

   
4. Crawl under the car, locate and remove the 7 10mm bolts that hold the plastic cowling in place. These are located 3 in the front and 2 on each side in the back of the cowling.
   

   
5. Using the flat head screwdriver, carefully remove the 2 plastic pins that help hold the cowling, there is one on each side on the front. The pins a 2 piece, you will need to gently pry the inner section out with the screwdriver then you should be able to remove the outer section with your fingers.
   

   
6. Carefully remove the cowling, it is now being held in place with 2 tabs in the front (where the plastic pins you just removed were) and 2 interlocking sections in the rear where the cowling meets the wheel well lining. Place the cowling in a safe place.
7. Place your oil drain pan under the drain plug, remove the plug using a 17mm socket
   

   
   • Be aware, the oil shot about 18 inches from the oil drain was first removed, you will need to place your oil drain plan accordingly and be prepared to move the pan closer to the drain as pressure decreases
8. Once the oil has fully drained (down to a drip) clean the drain plug and the area of the oil pan around the drain hole and replace the plug. I'm not aware of the torque recommendations for the drain plug but I will try to find them and update the guide.
9. Move the oil drain pan underneath the oil filter, use a 6mm hex head socket to remove the drain plug from the filter housing.
   

   
10. Once the oil filter has drained use the 76mm filter cap wrench to remove the filter cartridge housing. Admall amount of oil will come out as you remove the housing and there is a little bit of oil left in the housing itself.
11. Replace the O-Rings for the filter housing and filter housing oil drain plug, you may need to use the screwdriver to remove the old O-Rings.
12. Clean all pieces thoroughly as any dirt can cause leakage and engine damage. Use some oil to lubricate both O-Rings.
13. Replace oil filter cartridge, I don't believe there is an up or down.
14. Hand tighten the oil filter housing to the engine, you need to press up slightly against spring tension, be careful to not cross thread as the housing is plastic and can be easily damaged.
15. Install the filter housing drain plug, using a torque wrench and the 6mm hex bit socket, torque to 10 n-m (88.5 lb-in / 7.4 lb-ft), as you tighten the plug the filter housing itself will probably tighten some.
16. Tighten the filter housing, using a torque wrench and the 76mm cap type oil filter wrench, torque to 30 n-m (265.5 lb-in / 22.1 lb-ft)
    • Torque settings obtained from stampings in oil filter housing, be sure to double check that yours are the same
17. Re-install the cowling (you are finished under the car)
18. Add 4 quarts of oil to the car, make sure the oil is visible in the normal range on the dipstick.
19. Lower the car to level, check oil again and add more oil as necessary to bring oil to optimum level (for me typically an extra 1/4 quart to bring to high side of "normal" range on the dipstick).
20. Verify you have no leaks under the car

[edit] Videos

[edit] See Also